|
|
09-23-2006, 08:21 AM
|
#1
|
The Falcon
Join Date: Jul 2005
Location: Denmark
Posts: 15,430
|
Compresser help?
What is a good compresser?
I know its hould be oil free and as silent as possible.
Other than that, what should the spec's be on a compresser?
What is psi?
What is bar?
Do I need to put the compresser in an electrical conduit, or does the compresser somehow run on its own?
I have a hard time figuring all this out?
Danish forum's just refers to a guide where you can make your own compresser with a motor from a refridgerator and other compressors with no real detail to it.
I appreciate any info on I can get.
|
|
|
09-23-2006, 09:00 AM
|
#2
|
Master Painter
Painter
Join Date: Aug 2004
Location: Baltimore MD
Posts: 2,971
|
I would take a look at some of the compressors over at Dixie Art. The Iwata Sprintjet or Smartjet should be what you're looking for. I've heard good things about them. Also check out the Badger inventory. Make sure you get a regulator and a water trap. Most of these come w/both.
Specs would all depend on how much spraying you're going to do. If you plan on occasional spraying, I would say you don't need an airtank to come w/ the compressor. If you intend to spray a lot, a compressor/tank combo helps keep the compressor running longer.
PSI- Pounds per Square Inch. It's the setting you will use to push an amt. of air through your airbrush. Usually anywhere from 15-25psi.
Bar - You got me on that one...
The compressor will indeed need an electrical outlet. Since it appears you are overseas, make sure the compressor will run on your power grid. (i.e. 110 vs 220)
You can use various sources for air (compressed air can, C02 cannister, etc...) but unless you know what you're doing, a compressor will be easier for you. If you have access to a C02 cannister, that's not a bad choice either. You will occasionally need to refill it, and will need to install a regulator for it.
Hope that helps!
|
|
|
09-23-2006, 12:23 PM
|
#3
|
The Rock
Adamantium Plus Member
Join Date: Sep 2004
Location: Bend, Oregon
Posts: 9,686
|
I use the silentaire Scorpion II compressor and it works great for me I got it from Dixieart.com.
__________________
|
|
|
09-23-2006, 12:35 PM
|
#4
|
It's not hard to meet expenses, they're everywhere.
Join Date: Aug 2005
Location: L.A.
Posts: 4,627
|
hmmm, is it bad to use my DeWalt compressor? That's what I've been using.
|
|
|
09-23-2006, 12:46 PM
|
#5
|
The Rock
Adamantium Plus Member
Join Date: Sep 2004
Location: Bend, Oregon
Posts: 9,686
|
I was told the bigger commercial compressors aren't as consistant with the air flow, they tend to surge and the air doesn't come out as smoothly.
__________________
|
|
|
09-23-2006, 02:16 PM
|
#6
|
Captain Marvel
Join Date: Nov 2005
Posts: 3,237
|
I also got a Scorpion II thanks to ickwinzs recommendations.
|
|
|
09-23-2006, 03:12 PM
|
#7
|
The Falcon
Join Date: Jul 2005
Location: Denmark
Posts: 15,430
|
Thanks for all the info.
|
|
|
09-23-2006, 03:37 PM
|
#8
|
The Falcon
Join Date: Jul 2005
Location: Denmark
Posts: 15,430
|
I have some info on bar.
Bar is air pressure.
There is a danish online store that has a compressor that has an air pressure on 2.0 bar.
|
|
|
09-23-2006, 03:43 PM
|
#9
|
The Falcon
Join Date: Jul 2005
Location: Denmark
Posts: 15,430
|
The airbush does it have to be connected to an electrical conduit also?
|
|
|
09-23-2006, 04:28 PM
|
#10
|
The Falcon
Join Date: Jul 2005
Location: Denmark
Posts: 15,430
|
what size should the tip/needle be for detail work?
|
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
All times are GMT -4. The time now is 09:26 AM.